Reasons Your Fiat 500 Key Fob Won't Work

A key fob with the fiat 500 key fob reset panda key fob replacement (click here) 500 number is a handy way to open the doors and start the car. There are a myriad of reasons the fob could stop working. This includes a dead coin-battery water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement fiat 500 key Fiat Flip Key Remote - similar to the Ilco brand that must be programmed professionally by a local automotive locksmith (click here for Locksmith Search). It includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not functioning. Modern key fobs have a limited operating range and should be within only a few feet from the car to operate. If you're far away from your vehicle and Fiat Panda Key Fob Replacement press the key fob button the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery of your coin cell (Part number CR2032) by a new one from a reputable brand like Panasonic, Duracell, or Energizer. You can find them at the local hardware store or online.

After you've replaced the battery in the coin cell It is possible to test it by standing near your Fiat 500 and pressing the buttons. The car will flash its parking lights and the key fob should operate the lock and unlock switches.

If your key fob isn't working even after replacing the battery, there may be water damage which prevents it from communicating with the module in your vehicle. Water damage can happen in a variety of ways, ranging from the slightest splash to submerging the fob salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to pull the moisture out. If this isn't working, you'll need to have the fob reprogrammed either by an auto locksmith or dealer.

Water Damage

The fob does have rubber seals to keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the circuit board of the fob, causing it to short out and eventually die. Getting the fob wet is not an ideal idea, but if you drop it in a cup of water or forget to remove it from your pants pocket prior to running the washer and you don't have a chance, don't give in.

First, remove the battery from the fob. Before replacing the battery clean the electronic chip with isopropyl, or a similar product. Check the fob again to see if it is working. If the key isn't working, it may need to be reset. This is typically done by a professional or dealer auto locksmith.

If the key you have is older and has not been programmed for your car then you'll need to replace it completely. This is an easy process that can be carried out by a professional locksmith for automotive use. The locksmith needs to cut the key to match the ignition in your vehicle. They'll also need to program the fob into the car's system. This is a cost-effective and quick process that could be completed the same day.

Receiver Module Issues

One of the most common reasons your 500 key fob could stop functioning is that it's out of range. The remote's range is of 30 feet, so in the event that you are far from your vehicle it will not respond to your commands. This can be fixed by moving it closer to your vehicle until it begins responding.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob isn't working, it could have an internal circuit board problem. Reprogramming the fob usually resolves the issue. You can find instructions on how to do this for all automobiles by searching YouTube or looking through the owner's manual.

It's possible that you need to replace the metal clips that hold the coin battery. If they loose tension it could prevent the coin battery from sitting properly and could cause your remote to malfunction.

In rare cases the fob might become disconnected from your vehicle because of software or hardware issues. This can cause a major problem, but you can often fix this by visiting an auto locksmith to have them reprogram your fob. In certain situations they might need to reinstall the software in your body control module too.

Interference

Interference can also cause the key fob to be unable to receive or transmit a signal. This could occur if the key fob is located near an electronic radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. The key fob might not function because of a problem to the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. It could be a defective 500 receiver module if you've tried replacing the battery, reprogramming or using an alternative key fob. The receiver module, located under the dashboard, picks up radio frequency signals from your key fob. It transforms the signals into electronic commands, which are then translated by the vehicle.

Fortunately, there's an easy method of resetting all of the on-board systems in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Reconnect the battery. This will clear any residual electricity, and restart the computer of your car. This could help you get your key fob to work again. If the issue continues you should seek out a certified technician. They will be able to identify the root cause of any issues.